Search Results

3-D horn is a vehicle to vehicle communication-based technology which helps in reducing the noise pollution, which occurs, due to honking of automobile horns by letting only the drivers of the automobile to hear the horns and not the whole environment around him. To achieve this, several relatively small horn speakers are placed inside the car. These speakers are controlled by drivers of other cars. In this way honking will be heard only by the drivers. The most unique feature of this technology is the 3-D effect caused by the speakers which will let the driver know the location of the outside car which is honking. The 3-D effect is achieved by varying the intensity and proper allotment of sound to the positioned speakers in such a way that it will give the feel of the location of the outside car to the driver. Human detection is another important feature this technology provides. It will recognize whether the horn is honked for an automobile or for a human.

Sudden tire deflation, or blow-out, is sometimes cited as the cause of a crash. Safety researchers have previously attempted to study the loss of vehicle control resulting from a blow-out with some success using computer simulation. However, the simplified models used in these studies did little to expose the true transient nature of the handling problem created by a blown tire. New developments in vehicle simulation technology have made possible the detailed analysis of transient vehicle behavior during and after a blow-out. This paper presents the results of an experimental blow-out study with a comparison to computer simulations. In the experiments, a vehicle was driven under steady state conditions and a blow-out was induced at the right rear tire. Various driver steering and braking inputs were attempted, and the vehicle response was recorded. These events were then simulated using EDVSM. A comparison between experimental and simulated results is presented.

The objective of this study was to investigate if 3D auditory displays could be used to enhance parking assistance systems (PAS). Objective measurements and estimations of workload were used to assess the benefits of different 3D auditory displays. In today’s cars, PAS normally use a visual display together with simple sound signals to inform drivers of obstacles in close proximity. These systems rely heavily on the visual display, as the sound does not provide information about obstacles' location. This may cause the driver to lose focus on the surroundings and reduce situational awareness. Two user studies (during summer and winter) were conducted to compare three different systems. The baseline system corresponded to a system normally found in today’s cars. The other systems were designed with a 3D auditory display, conveying information of where obstacles were located through sound. A visual display was also available. Both normal parking and parallel parking was conducted.

This document describes the 3D computer-aided design (CAD) parts and file formats for the HPM-1 H-point machine available from SAE. The intended purpose for this information is to provide a master CAD reference for design and benchmarking.

According to accident analysis, submarining is responsible for most of the frontal car crash AIS 3+ abdominal injuries sustained by restrained occupants. Submarining is characterized by an initial position of the lap belt on the iliac spine. During the crash, the pelvis slips under the lap belt which loads the abdomen. The order of magnitude of the abdominal deflection rate was reported by Uriot to be approximately 4 m/s. In addition, the use of active restraint devices such as pretensioners in recent cars lead to the need for the investigation of Out-Of-Position injuries. OOP is defined by an initial position of the lap belt on the abdomen instead of the pelvis resulting in a direct loading of the abdomen during pretensioning and the crash. In that case, the penetration speed of the belt into the abdomen was reported by Trosseille to be approximately 8 to 12 m/s. The aim of this study was to characterize the response of the human abdomen in submarining and OOP.

In order to improve the fit and comfort of helmets, we developed digital head models that represent the anthropometric and morphometric variability found in the U.S. Navy. We analyzed the size and shape variation using two related approaches. First, we used Procrustes superimposition, which minimizes the distances between all landmarks of all subjects. This allowed us to visualize the variation in landmark distribution of the face and to test for statistical differences. Second, we extracted curvatures along the surface of the head. This allowed us to characterize the variation in the shape of the head. To create a series of sized digital models, we used principal component analysis (PCA) to organize the variation in both the traditional measurements as well as the locations of the 3D landmarks. Using an adaptation of multivariate accommodation modeling we identified representative individuals who characterize 95% of the variation in size and shape.

The vehicle Heating, Ventilation and Air conditioning (HVAC) system is designed to meet both the safety and thermal comfort requirements of the passengers inside the cabin. The thermal comfort requirement, however, is highly subjective and is usually met objectively by carrying out time dependent mapping of parameters like the velocity and temperature at various in-cabin locations. These target parameters are simulated for the vehicle interior for a case of hot soaking and its subsequent cool-down to test the efficacy of the AC system. Typically, AC performance is judged by air temperature at passenger locations, thermal comfort estimation along with time to reach comfortable condition for human. Simulating long transient vehicle cabin for thermal comfort evaluation is computationally expensive and involves complex cabin material modelling.

To ensure reliable Diesel Particulate Filter (DPF) regeneration, even in critical situations such as slow city driving, a fuel vaporizer can be used to introduce additional hydrocarbons directly into the Diesel aftertreatment system. The fuel vaporizer provides significantly shorter reaction times than possible with engine measures alone and also helps minimize the extensive engine measures normally required to achieve the DPF ignition temperatures. As with other components, correctly optimizing complex aftertreatment systems requires not simply characterizing and optimizing an individual component, but also understanding the interaction between components and the behaviour of the system as a whole. The value of a system simulation lies in rapid turnaround times combined with the ability to address three-dimensional phenomena, since they often have a decisive impact on the system performance (e.g., the hydrocarbon distribution and its associated catalytic heat release).

A novel CFD simulation technique has been developed that unites realistic three-dimensional resolution of diesel particulate filter systems with computational efficiency. Three-dimensional resolution of the thermofluiddynamic behaviour during transient soot loading and regeneration is necessary for the optimization of the function, durability, weight and cost of DPF systems. Computational efficiency is required to allow its use as a standard development tool during all engineering phases and to allow the simulation of driving cycles. The detailed conclusions that can be drawn about soot distribution and thermal characteristics during the regeneration assist in ensuring the DPF function and avoiding DPF failures over the operational lifetime.

This work describes the definition and implementation of a dedicated system (hardware and software) for the quantitative evaluation of the anthropometrics and morphological parameters of the back shape. This was applied to the digital 3D analysis of subjects affected by spinal pathologies. In fact in clinical practice it is needed to have a repeatable and easy method to frequent non invasive screening of the rib system records a 3D model of the back shape standard and automated procedure. Its clinical validation is presented.

Three-dimensional (3D) whole body scanners provide an opportunity for collecting large quantities of precise point data on human forms. However, product designers will likely always need some access to traditional point-to-point dimensional measurements. These measurements can also be obtained from the 3D whole body scanner if appropriate software is developed. This project describes a validation test for a collection of software tools designed to extract traditional dimensions from 3D whole body scans. To validate the software we scanned 123 male and female subjects on a Cyberware WB4 whole body scanner. Subjects were also measured for point-to-point dimensions using traditional instruments. We compared the mean absolute differences between traditional and software measurements to interobserver error data collected in a large traditional anthropometric survey (ANSUR), and to various criteria specific to garment applications.

Due to the accidents of the motor vehicles and the osteoporosis, many people enface a lot of troubles and sometimes necessities for replacement of their knee joints. Practically, mechanical properties and surface characteristics of Total Knee Replacement (TKR) are very important parameters for improving the performance response in human. The meniscus is a small element and an essential part of the TKR. The knee meniscus has special feature allows the easy dynamic loading and motion of leg and foot with high accuracy and good balance. Therefore design and analysis of the geometrical shape for the meniscus replacement is worthy to be studied. In this paper, a proposed design using a computer software package has been presented. 3D simulation analyses of a variety of meniscus thickness and different materials under different loads are investigated. The compression stresses and surfaces deformations are determined numerically through the Finite Element Analysis (FEA) technique.

Today's agri-businessman is challenged to improve his efficiency to meet higher operating costs and to counter the effects of inflation. New concepts in John Deere's line of 4-wheel-drive tractors are targeted toward this goal and provide increased productivity through power increases, improved fuel economy, comfortable convenient operator environment and controls, increased hydraulic power, improved serviceability and repairability and monitoring of more critical vehicle functions.

Electrical Air Conditioning Systems for 42 V vehicles will provide many benefits in terms of Environment protection, car Architecture, cabin Comfort and overall Safety. E-A/C Systems essentially differ from conventional ones by the use of electrical compressors. First of all, they will be particularly well adapted to new powertrains, helping to make them more environmentally friendly. Accurate control and high efficiency under the most common thermal conditions will reduce the A/C impact on fuel consumption. Besides, higher sealing integrity will cut emissions of refrigerant during normal operation and maintenance. Secondly, the use of an electrically driven compressor (EDC) will suppress a belt, and will reduce the packaging constraints. This will help to design new vehicle architectures. Thirdly, the electrification of air conditioning will allow better thermal comfort. In particular, E-A/C Systems provide a good opportunity for cabin pre-conditioning.

FOUR-WHEEL STEERING (4WS) is beginning to find widespread use as a new approach to improving vehicle dynamics, especially in the medium and high speed ranges. Steering the rear wheels in the same phase as the front wheels enhances vehicle stability. Four-wheel steering systems have an even greater potential to improve stability and steering response through suitable control over the transient characteristics of the rear wheel steer angle. This paper traces the course of Nissan research and development work on four-wheel steering and the evolution of Nissan's HICAS (4WS) technology. It also describes research activities under way on vehicle dynamics using a newly developed Simulator Vehicle, equipped with a front and rear angle transient control system which makes it possible to vary the dynamic characteristics of the vehicle instantaneously and at will while driving.

A new compact skid steer loader has been developed. Along with productivity and cost, the design of this loader was concentrated on improving ease of operation, operator comfort and safety, and serviceability. This paper discusses how serviceability was improved over previous model Bobcats. That is; improved accessibility to regulary serviced items, reduced service parts and improved reliability.

Four new 2-cylinder 4-stroke concepts are displayed as design and fitted in vehicles. These four different concepts comprise a Modular Concept V2- and W3-cylinder a MotoGP / Superbike concept with 2 and 3 cylinders, a narrow angle V-engine and a Building Block System Commuter CVT engine. Each engine concept is designed to meet the different requirements of the four segments. Specific analysis and simulation concerning 1D thermodynamics, vehicle simulation and delivered performance and tractive force was done for each concept. The concepts are compared in the aspects of uniform rotation, inertia forces and moments, and the effect on performance by the pulse effects of the manifolded intake and exhaust systems. The Modular Concept contains an OHC engine with a wide range of displacements and commonality of many parts. Good versatility is obtained as the concepts can be applied for sport- or custom bikes.

To optimize the tyre contact patch in a sports car, Ferrari has developed an active camber and toe (ACT) system comprising of 4 actuators for the rear axle. This complex and completely new system is difficult to model accurately and for this reason, it was decided to combine a physical prototype with a full vehicle model to carry out the functional tests. The method of combining a virtual model with a physical test is known as hybrid simulation. This functional testing of both the actuators and the vehicle dynamics logic will be performed on an MTS 6DOF bench test prior to physical track testing on a prototype vehicle using Ferrari facility in Maranello, Italy. In support of this functional testing, we will use hybrid simulation techniques with software and methods specifically developed. The planned hybrid test system described in the paper will allow dynamic coupling between the physical bench test and a modified full vehicle simulation model.

Weight reduction and high transmission efficiency demands are getting heavier to manual transmission (MT) for vehicle driving and fuel economy performance. Also comfortable shift feeling and low gear noise level are continuously required by customer because those sensitivity performances are directly recognized by driver which can determine the transmission's merchantability. Newly developed high torque capacity MT is based on serial transmission BG6 which is adopted into a lot of customer' vehicle. This new MT is weight reduced, shift feeling and gear noise performance are highly improved that keeps strong competitiveness in the future. Concerning shift feeling, its smoothness, force balance and cross shift performance are improved and optimized. Also for low gear noise performance, it was reduced to the level which can have advantage to competitor and highly comfortable for passenger vehicle. Those improvement technologies are reported as follows.

In France, the current evolution in the number of road accident victims is less favourable for the moped rider category than for the majority of others. In addition, the proportion of scooters in the moped park is currently considerably increasing. The aim of the research work presented is to consider if an explanation for the bad results for this category of users, in terms of road safety, can be found through the study of the dynamic performances of this type of vehicle. We thus carried out an experiment aimed at comparing the dynamic capacities of a “Classic” moped with those of a “Scooter” model. Two mopeds, one of each type, were fitted with an embedded measurement system. They were driven for several tests on a track by a professional test pilot. The results of this study are more in favour of the “Scooter” moped, which seems to offer equivalent, or even better, dynamic capacities than the “Classic” one.